• Home
• Function/Function Block Reference
• Safety-Related PLCopen Function Blocks
• SF_MutingSeq
• Diagnostic codes

Diagnostic codes

The hexadecimal diagnostic codes listed here are output as WORD data type at the DiagCode output of the function block.

Code (hex)	Description	Options for remedy
0000	The function block is not active. The Activate input is FALSE.	Activate the function block by setting Activate to TRUE.
8000	The function block is in a normal operating state. The muting process is not active (S_MutingActive = SAFEFALSE). The safety-related equipment of the zone of operation signals the defined safe state (S_AOPD_In = SAFETRUE). The enable signal is active (S_AOPD_Out = SAFETRUE).	In case of an unexpected combination at the function block inputs relative to the physical input of the sensors, verify the connected hardware if required and correct the error.
8001	The function block was activated. The start-up inhibit of the function block is active.	Perform a reset on the function block to exit the active start-up inhibit for the function block.
8002	The muting process was not active but the safety-related equipment of the zone of operation signals the non-safe state (S_AOPD_In = SAFEFALSE).	To exit the active start-up inhibit for the function block, perform a reset on the function block once you have removed the request for the safety-related function at S_AOPD_In.
8005	The muting process is not active (S_MutingActive = SAFEFALSE). The safety-related equipment of the zone of operation signals the defined safe state (S_AOPD_In = SAFETRUE). The enable signal is not active (S_AOPD_Out = SAFEFALSE). This state is completed after one cycle of the Safety PLC.	In case of an unexpected combination at the function block inputs relative to the physical input of the sensors, verify the connected hardware if required and correct the error.
8011	The muting process in conveying direction 1 was requested at MutingSwitch11 (MutingSwitch11 = TRUE, MutingSwitch12 = FALSE, MutingSwitch21 = FALSE and MutingSwitch22 = FALSE). MaxMutingTime monitoring has started.	In case of an unexpected combination at the function block inputs relative to the physical input of the sensors, verify the connected hardware if required and correct the error.
8012	The muting process in conveying direction 1 is active (MutingSwitch11 = TRUE and MutingSwitch12 = TRUE). MaxMutingTime monitoring is running. The safety-related equipment of the zone of operation is not evaluated.	In case of an unexpected combination at the function block inputs relative to the physical input of the sensors, verify the connected hardware if required and correct the error.
8112	The muting process in conveying direction 2 is active (MutingSwitch21 = TRUE and MutingSwitch22 = TRUE). MaxMutingTime monitoring is running. The safety-related equipment of the zone of operation is not evaluated.	In case of an unexpected combination at the function block inputs relative to the physical input of the sensors, verify the connected hardware if required and correct the error.
8122	The muting process in conveying direction 2 was requested at MutingSwitch22 (MutingSwitch11 = FALSE, MutingSwitch12 = FALSE, MutingSwitch21 = FALSE and MutingSwitch22 = TRUE). MaxMutingTime monitoring has started.	In case of an unexpected combination at the function block inputs relative to the physical input of the sensors, verify the connected hardware if required and correct the error.
C001	The function block has detected a static TRUE signal at Reset.	Verify the reset control device and the associated wiring. The Reset signal must be set to FALSE.
C003	The function block has detected an invalid SAFEFALSE signal at S_MutingLamp.	- Verify the hardware (muting lamp). - The signal connected to S_MutingLamp must be SAFETRUE. - Perform a reset on the function block.
C004	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C005	The function block detected an invalid value at MaxMutingTime. MaxMutingTime= 0-600s	- Verify the value configured at MaxMutingTime. - Correct the incorrect value. The value should correspond to the results of your risk analysis. The limit values for parameters should be taken into account when performing your risk analysis.
C006	The muting process was not completed before time monitoring for the maximum muting time set at MaxMutingTime elapsed.	- Verify the muting process. - Verify the time value specified at MaxMutingTime. This value should correspond to the results of your risk analysis. - Verify the hardware. - Perform a reset on the function block when MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 are set to FALSE.
C010	The function block has detected a static TRUE signal at Reset.	Verify the reset control device and the associated wiring. The Reset signal must be set to FALSE.
C014	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C020	The function block has detected a static TRUE signal at Reset.	Verify the reset control device and the associated wiring. The Reset signal must be set to FALSE.
C024	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C030	The function block has detected a static TRUE signal at Reset.	Verify the reset control device and the associated wiring. The Reset signal must be set to FALSE.
C034	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C040	The function block has detected a static TRUE signal at Reset.	Verify the reset control device and the associated wiring. The Reset signal must be set to FALSE.
C044	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C054	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C064	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C074	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C084	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C094	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C0A4	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C0B4	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C0C4	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C0D4	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C0E4	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C0F4	Invalid muting sequence detected. Muting was not requested or the muting process has just been completed. The muting sensors then change to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C104	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C114	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C124	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C134	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C144	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C154	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C164	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C174	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C184	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C194	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C1A4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C1B4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C1C4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C1D4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C1E4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C1F4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C204	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C214	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C224	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C234	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C244	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C254	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C264	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C274	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C284	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C294	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C2A4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C2B4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C2C4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C2D4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C2E4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C2F4	Invalid muting sequence in conveying direction 1. After requesting the muting process by MutingSwitch11 and MutingSwitch12, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C304	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C314	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C324	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C334	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C344	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C354	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C364	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C374	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C384	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C394	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C3A4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C3B4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C3C4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C3D4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C3E4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C3F4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C404	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C414	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C424	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C434	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C444	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C454	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C464	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C474	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C484	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C494	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C4A4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C4B4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C4C4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C4D4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C4E4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
C4F4	Invalid muting sequence in conveying direction 2. After requesting the muting process by MutingSwitch22 and MutingSwitch21, the muting sensors changed to the following invalid state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF04	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF14	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF24	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF34	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF44	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF54	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF64	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF74	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = FALSE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF84	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CF94	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CFA4	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CFB4	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = FALSE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CFC4	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CFD4	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = FALSE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CFE4	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = FALSE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.
CFF4	Invalid muting sequence detected. During an active muting process MutingEnable became FALSE. In this situation the muting sensors had the following state: MutingSwitch11 = TRUE MutingSwitch12 = TRUE MutingSwitch21 = TRUE MutingSwitch22 = TRUE	- Verify the muting process. - Set MutingSwitch11, MutingSwitch12, MutingSwitch21 and MutingSwitch22 to FALSE. - Then perform a reset on the function block.